Just How to Set up a Bathtub
Just How to Set up a Bathtub
Blog Article
We've found this article about A Step-by-Step Guide to Installing a Bathtub below on the internet and think it made sense to write about it with you in this article.
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old bath tub with a brand-new one is also a reasonably challenging project. If the old bathtub is easily accessible, the job can relocate rapidly; if you have to open up a wall to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the project is within a house handyman's abilities, although you will require a helper to leave the old tub and also set in the brand-new one. Ensure you have certified yourself for the task and are comfortable trying it. Rather than employing a specialist to take control of a halfway-completed task, it is better to take into consideration employing one before you start. Chances are you may require a professional plumber to make tube connections.
This write-up will aid you install a new bath tub in your bathroom if you have currently acquired a new tub and also do not need to alter the setup of your previous water system pipelines.
Your tools as well as product list should make up the following:
Preparing for the Installation
First of all, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is necessary to make sure that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, switch on the taps to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipes to the faucets. Have a towel prepared for the staying water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming during this procedure. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any type of old sealing compound.
Prior to carrying on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Bathtub
Making use of both wooden boards under its feet, position the tub in the required position. The wood boards are valuable in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 little points.
The following goal is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level and readjusting the feet on the tub until the level reads degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Activate the supply of water and also check all joints and also new pipework for leakages as well as tighten them if essential. Fill up the bath tub and additionally inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as sealing around the tub needs to wait up until the bath tub has been utilized at least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly require lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washers remain in area in between the tap and also the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, causing problems with moisture and also feasible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of soaked paper or soft rope. Keep in mind to constantly fill the tub with water before securing, to permit the motion experienced when the bathtub is in use. The sealant can crack relatively early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the marketplace. It is recommended to fit the floor tiles making use of water-resistant or waterproof adhesive and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you enjoyed reading our piece about How to Install a Bathtub. Thank you for taking time to browse our blog. Enjoyed reading our piece of writing? Please share it. Help other people discover it. Kudos for your time. Don't forget to come visit our site back soon.
Services
Report this page